30Ni16Cr5 is a low-alloy steel characterized by its composition, which includes approximately 30% nickel and 16% chromium. This steel is known for lanciao its excellent
Read more
Mechanical Engineering
+2
Cutting tools and machine tools is the same?
Asked by Anonymous
No, cutting tools and machine tools are not the same. Cutting tools are devices used to remove material from a workpiece during machining. Machine tools are
Read more
Mechanical Engineering
What is the best way to sharpen reciprocating saw blades?
Asked by Anonymous
The best way to sharpen reciprocating saw blades is by using a fine file or specialised sharpening tool to carefully restore the cutting edges of each tooth whi
Read more
Industrial Engineering
+2
What is the effectg of packing density on the performance of a cooling tower?
Asked by Anonymous
Packing density in a cooling tower significantly influences its heat transfer efficiency and overall performance. Higher packing density increases the surface a
Read more
Motorcycle Gear and Apparel
+2
What is a closed loop itinerary?
Asked by Anonymous
A closed loop itinerary is a travel plan that begins and ends at the same location, allowing travelers to explore a specific region or area without needing to r
Read more
Mechanical Engineering
What lubricant should be use for cast iron?
Asked by Anonymous
For cast iron, a non-toxic, food-safe lubricant such as vegetable oil or mineral oil is often recommended, particularly for cookware like cast iron skillets. In
Read more
Mechanical Engineering
What are the material characteristics that need to be taken into account when marking out sheet plate or rolled steel?
Asked by Anonymous
When marking out sheet plate or rolled steel, key material characteristics to consider include thickness, surface finish, and grain direction. The thickness aff
Read more
Mechanical Engineering
What is the fusibility of stainless steel?
Asked by Anonymous
Fusibility refers to the ability of a material to melt and flow when subjected to heat. Stainless steel typically has a melting point between 1,400°C and 1,600°
Read more
Mechanical Engineering
What is thicker 9 gauge or 11.5 Gauge chainlink fence?
Asked by Anonymous
A 9 gauge chain link fence is thicker than an 11.5 gauge fence. In gauge measurements, a lower number indicates a thicker wire, so 9 gauge wire is stronger and
Read more
Mechanical Engineering
What is SAE equivalent steel grade for Gr 8.8 per BS 3692?
Asked by Anonymous
The SAE equivalent steel grade for Grade 8.8 according to BS 3692 is typically SAE J429 Grade 5. Grade 8.8 is a medium strength bolt made from carbon steel, whi
Read more
Mechanical Engineering
+1
Why copper is diffcult to spot welding?
Asked by Anonymous
Copper is difficult to spot weld due to its high thermal conductivity, which allows heat to dissipate quickly, making it challenging to achieve the localized me
Read more
Mechanical Engineering
Centrifugal compressor seal to how?
Asked by Karthickboxer
Centrifugal compressor seals are designed to prevent gas leakage between the rotating impeller and the stationary components, ensuring efficient operation. Thes
Read more
Mechanical Engineering
+1
How are steam turbine bearings insulated?
Asked by Anonymous
Steam turbine bearings are typically insulated using materials that have low thermal conductivity, such as rubber or composite materials. This insulation helps
Read more
Mechanical Engineering
+1
What assumptions does the Morse test make?
Asked by Zwehphohlo
The Morse test assumes that the relationship between the independent variable (often time or a certain condition) and the dependent variable (such as a biologic
Read more
Mechanical Engineering
Why thrust bearing located non drive end side of centrifugal compressor?
Asked by Anonymous
The thrust bearing is typically located on the non-drive end side of a centrifugal compressor to effectively manage axial loads generated during operation. This
Read more
Mechanical Engineering
What are thd factor on which rigidity modulus depends?
Asked by Anonymous
The rigidity modulus, also known as the shear modulus, depends primarily on the material's intrinsic properties, including its composition, temperature, and mic
Read more
Mechanical Engineering
Why flow of centrifugal fans is not blocked at their discharge?
Asked by Anonymous
The flow of centrifugal fans is not blocked at their discharge because these fans are designed to create a high-velocity airflow that exits the fan outlet. The
Read more
Mechanical Engineering
What gauge is 07mm?
Asked by Anonymous
A 07mm gauge typically refers to a wire gauge measurement that is equivalent to approximately 0.28 inches or 7 millimeters in diameter. However, wire gauge syst
Read more
Mechanical Engineering
How can you perform aging test of CR GO silicon steel sheet?
Asked by Anonymous
To perform an aging test on CR GO (Cold Rolled Grain Oriented) silicon steel sheets, you can expose the samples to elevated temperatures (typically between 150°
Read more
Mechanical Engineering
+2
What type of radiation is produced by the electric arc in welding?
Asked by Anonymous
The electric arc in welding produces several types of radiation, primarily ultraviolet (UV) radiation, visible light, and infrared (IR) radiation. The intense h
Read more
Mechanical Engineering
What are the examples of levers that magnify movement?
Asked by Anonymous
Examples of levers that magnify movement include the seesaw, where a small force applied at one end can lift a heavier weight on the other end, and the crowbar,
Read more
Mechanical Engineering
What is hornby n gauge?
Asked by Anonymous
Hornby N gauge refers to a scale of model railways produced by Hornby, a well-known manufacturer of model trains and accessories. N gauge represents a scale rat
Read more
Mechanical Engineering
What is renwood tooling?
Asked by Anonymous
Renwood Tooling is a company that specializes in providing high-quality tooling solutions for various manufacturing processes, particularly in the woodworking a
Read more
Mechanical Engineering
What is FG 200 steel?
Asked by Anonymous
FG 200 steel, also known as G200 cast iron, is a type of gray cast iron characterized by its graphite content, which typically falls between 2.5% and 4%. It is
Read more
Mechanical Engineering
What are the gauges set to for brazing?
Asked by Anonymous
For brazing, the gauges typically set the gas flow and pressure to ensure optimal flame characteristics for the process. Acetylene is commonly set at around 5 t
Read more
PreviousNext
Trending Questions
Is the bulk modulus of elasticity increases with pressure? Sensitization of steel? Where can one find a vacancy for a mechanical engineer? What is Indian standard steel to bs en 10025 grade s275? Is rubber ductile material or brittle material? What are examples of laminar and turbulent flow? What is 20 mm mild steel square hollow pipe 14 gauge standard weight? What is the OD of a ¾inch schedule 40 pipe? What is the SBDV valves? What is the most important gear in the world? How do you calculate load capacity on 1 inch steel plate floor? What is turbine runback? What is the formula for section modulus of a cylinder? What is the Difference between ibr and non IBR pipes? What are automated production systems? What is HIC vessel? What are the basic principles of operation of the centre lathe and its accessories and the typical operations that they can perform? What is tripping speed? Reasons of positive axial shift in steam turbine? What is slenderness ratio structural engineering?
Resources
Leaderboard All Tags Unanswered
Top Categories
Algebra Chemistry Biology World History English Language Arts Psychology Computer Science Economics
Product
Community Guidelines Honor Code Flashcard Maker Study Guides Math Solver FAQ
Company
About Us Contact Us Terms of Service Privacy Policy Disclaimer Cookie Policy IP Issues
Copyright ©2026 Infospace Holdings LLC, A System1 Company. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.